New 2021 300-615 Dumps for CCNP Data Center Certified Exam Questions & Answer
Realistic Verified 300-615 exam dumps Q&As - 300-615 Free Update
Cisco 300-615: Troubleshooting Cisco Data Center Infrastructure Certified Professional salary
The average salary of a Cisco 300-615: Troubleshooting Cisco Data Center Infrastructure Certified Expert in:
- Europe - 66,000 EURO
- United State - 80,000 USD
- India - 16,00,000 INR
- England - 62,000 POUND
To Sum Up
Choose the most suitable study resources and start your preparation for the Cisco 300-615 exam. With official training and books, you’ll get ready to pass it in one go. Remember to ace the second required test as well, and the CCNP Data Center certificate will come with all its related perks.
Introduction to Cisco 300-615: Troubleshooting Cisco Data Center Infrastructure Exam
The Troubleshooting Cisco Data Center Infrastructure (DCIT) v7.0 course shows you how to troubleshoot LAN, SAN, Cisco Data Center Unified Fabric, Cisco Unified Computing System (Cisco UCS), and Cisco Application-Centric Infrastructure (Cisco ACI). You will learn methodologies and tools to identify issues that may occur in data center network architecture. You will get extensive hands-on practice troubleshooting installation, configuration, and interconnectivity issues on Cisco Multilayer Director Switch (MDS) switches, Cisco Nexusî switches, Cisco Fabric Extenders (FEXs).
NEW QUESTION 37
A customer reports that the Chassis Management Controller fails to receive chassis information from Cisco UCS Manager. Which set of steps resolves the issue?
- A. 1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level.
2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly.
3) Check for runtime link down status
4) Reseat the affected IOM. - B. 1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level.
2) Verify that at least two physical cables between the IOM and fabric interconnect function properly.
3) Check for runtime link down status.
4) Reseat the affected IOM. - C. 1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels
2) Verify that at least two physical cables between the IOM and fabric interconnect function properly.
3) Check for runtime link down status
4) Reseat the affected IOM. - D. 1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels.
2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly.
3) Check for runtime link down status.
4) Reseat the affected IOM.
Answer: A
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ts/guide/UCSTroubleshooting/UCSTroubleshooti
NEW QUESTION 38
Refer to the exhibits.
An engineer troubleshoots switch N5K1, which fails to receive traffic from the file server Which set of actions resolves this problem?
- A. Bind native VLAN 10 with Ethemet10/1/1 and allow VLAN 10 in trunk configuration
- B. Assign native VLAN 10 with vfc111 and allow VLAN 1101 in trunk configuration.
- C. Assign native VLAN 10 with fc2.'l - 2 and allow VLAN 10 in trunk configuration.
- D. Bind native VLAN 10 with Ethemet1/10 and allow VSAN 101 in trunk configuration.
Answer: D
NEW QUESTION 39
An engineer is troubleshooting issues in Cisco UCS Director. Drag and drop the possible causes from the left onto the correct issues on the right.
Answer:
Explanation:
NEW QUESTION 40
Refer to the exhibit.
The initiator that has FC ID 0x970102 fails to communicate with the target that has FC ID 0x970200. What action resolves the issue?
- A. Reconfigure the initiator and the target to be in the same zones.
- B. Reset the port for FC ID 0x970102 and FC ID 0x970200 to log in to the fabric.
- C. Reset the port for FC ID 0x970209 and FC ID 0x9700c2 to log in to the fabric.
- D. Reactivate the zoneset.
Answer: A
NEW QUESTION 41
Refer to the exhibit.
The EEM script is applied in the default VDC to collect the outputs during high CPU utilization on the Cisco Nexus 7000 Series Switch for all VDCs. Which configuration set must be added to the script to fix the issue?
- A. switch(config-apple)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli enable switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution
- B. switch(config-apple)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli config t switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution
- C. switch(config-apple)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli enable switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution
- D. switch(config-apple)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli config t switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution
Answer: A
Explanation:
Explanation
Need exact snap shot to confirm the following.
The selection of is due to
* SNMP command has the key word "oid".
* The command "switchto vdc Core" show run in "enable" mode, not "config t" mode.
NEW QUESTION 42
Refer to the exhibit.
The HSRP instance on both switches is showing as active. Which action resolves the issue?
- A. Allow VLAN 100 between the switches.
- B. Configure the HSRP timers to be the same.
- C. Configure preempt on only one of the switches.
- D. Configure the IP address of N9K-B on the same subnet as N9K-A.
Answer: A
NEW QUESTION 43
A network administrator attempts to install an application in the Cisco NX-OS Guest shell and receives an error that there is not enough space on the disk. Which command must the administrator run to increase the disk space available in the Guest shell?
- A. guestshell resize rootfs [size-in-MB]
- B. guestshell growdisk rootfs [size-in-MB]
- C. guestshell pvextend rootfs [size-in-MB]
- D. guestshell resize2fs rootfs [size-in-MB]
Answer: A
NEW QUESTION 44 
Refer to the exhibit. The HSRP instance on both switches is showing as active. Which action resolves the issue?
- A. Allow VLAN 100 between the switches.
- B. Configure the HSRP timers to be the same.
- C. Configure preempt on only one of the switches.
- D. Configure the IP address of N9K-B on the same subnet as N9K-A.
Answer: A
Explanation:
Section: Network
Explanation
NEW QUESTION 45
Refer to the exhibit. A network engineer creates an EEM script to trigger an SNMP notification when a user enters configuration mode, but the trap is not received when the condition is met. Which action resolves the issue?
- A. Modify cli match "conf t" to "snmp match "conf t"
- B. Append action 2.0 event-default to the script
- C. Modify snmp-trap strdata "Configuration changed" to syslog msg Configuration changed
- D. Append action 2.0 cli "conf t" to the script
Answer: B
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/6-x/system_management/configuration/guide/b_Cisco_Nexus_9000_Series_NX-OS_System_Management_Configuration_Guide/sm_12eem.html
NEW QUESTION 46
Refer to the exhibit.
A web browser displays a "not secure" warning message when accessing the web interface of Cisco UCS Manager. Which action resolves the issue?
- A. Use a supported web browser.
- B. Use a supported version of UCS Manager.
- C. Use the correct TCP port for HTTPS.
- D. Load third-party certificate to UCS Manager.
Answer: D
NEW QUESTION 47
Refer to the exhibit.
The EEM script is applied in the default VDC to collect the outputs during high CPU utilization on the Cisco Nexus 7000 Series Switch for all VDCs. Which configuration set must be added to the script to fix the issue?
- A. switch(config-apple)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli enable switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution
- B. switch(config-apple)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli config t switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution
- C. switch(config-apple)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli enable switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution
- D. switch(config-apple)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli config t switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution
Answer: A
Explanation:
Explanation
Need exact snap shot to confirm the following.
The selection of is due to
* SNMP command has the key word "oid".
* The command "switchto vdc Core" show run in "enable" mode, not "config t" mode.
NEW QUESTION 48
Refer to the exhibit.
The EEM script fails to send an SNMP trap when a user attempts to enter configuration mode. Which configuration is missing from the script?
- A. IP address of the SNMP server
- B. event-default action statement
- C. event statement
- D. policy-default action statement
Answer: A
NEW QUESTION 49
A request to activate the port security database is rejected. Which action investigates the cause of the issue?
- A. Verify that devices are fully attached to the active database.
- B. Find conflicting entries between the active and configuration databases.
- C. Enable the auto-learning feature.
- D. Use the force option to identify rejected devices.
Answer: D
Explanation:
Section: Management and Operations
NEW QUESTION 50
An engineer enables the packet postcards feature on a Cisco Nexus 9000 Series Switch but receives this error message:
"Error: Cannot configure postcard when inband-telemetry is configured." Which action resolves the issue?
- A. Disable the hardware-telemetry feature.
- B. Disable the telemetry feature.
- C. Disable the inband-telemetry feature.
- D. Disable the software-telemetry feature.
Answer: A
Explanation:
Section: Management and Operations
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/92x/programmability/ guide/b-cisco-nexus-9000-series-nx-os-programmability-guide-92x/b-cisco-nexus-9000-series-nx-os- programmability-guide-92x_chapter_0100001.html
NEW QUESTION 51
Refer to the exhibit.
The HSRP instance on both switches is showing as active. Which action resolves the issue?
- A. Allow VLAN 100 between the switches.
- B. Configure the HSRP timers to be the same.
- C. Configure preempt on only one of the switches.
- D. Configure the IP address of N9K-B on the same subnet as N9K-A.
Answer: A
NEW QUESTION 52 
Refer to the exhibit. A network engineer configures an EEM script to get a syslog notification after a configuration change. This message appears when the engineer must make a new configuration to this switch. Which configuration did the engineer neglect to apply in the script for it to function properly?
- A. event policy-default count 1 time 100
- B. event syslog occurs 10
- C. event cli match 'configure terminal'
- D. action 2.0 event-default
Answer: D
Explanation:
Section: Automation
NEW QUESTION 53
A fabric interconnect fails to start and the console displays the loader prompt. Which two actions resolve the issue? (Choose two.)
- A. Reformat the fabric interconnect.
- B. Load an uncorrupt kickstart image.
- C. Load the correct version of the boot image.
- D. Reconnect L1/L2 cables between the Fis.
- E. Load an uncorrupt bootloader image.
Answer: B,C
Explanation:
Section: Storage Network
NEW QUESTION 54
Refer to the exhibit.
An engineer is troubleshooting why user1, user2, and user3 from group STORAGE- ADMINISTRATOR in Microsoft Active Directory cannot log in to the Cisco MDS SSH CLI. Which action resolves the issue?
- A. Include specific users into MDS role configuration.
- B. Configure the role name to match the group name on Microsoft Active Directory.
- C. Configure SSH logins on Cisco MDS switch.
- D. Integrate Cisco MDS with Microsoft Active Directory.
Answer: B
NEW QUESTION 55
Refer to the exhibit.
An upgrade operation fails with an error displayed. Which action resolve the issue?
- A. Use a different system image
- B. Use a different kickstart image
- C. Allocate extra space on a flash drive to extract a kickstart image
- D. Allocate extra space on a flash drive to extract a system image
Answer: A
Explanation:
Explanation
Kickstart image verification succeeded. System image has failed.
NEW QUESTION 56
A firmware upgrade on a fabric interconnect fails. A bootflash contains a valid image. Drag and drop the recovery steps from the left onto the correct order on the right.
Answer:
Explanation:
NEW QUESTION 57
Refer to the exhibit.
The HSRP configuration in the exhibit fails to function. Which action resolves this issue?
- A. Configure HSRP version 2.
- B. Enable IP redirects.
- C. Configure the same HSRP group on both devices.
- D. Set the MTU to 1500 bytes.
Answer: A
NEW QUESTION 58 
Refer to the exhibit. An engineer is troubleshooting why user1, user2, and user3 from group STORAGE- ADMINISTRATOR in Microsoft Active Directory cannot log in to the Cisco MDS SSH CLI. Which action resolves the issue?
- A. Include specific users into MDS role configuration.
- B. Configure the role name to match the group name on Microsoft Active Directory.
- C. Configure SSH logins on Cisco MDS switch.
- D. Integrate Cisco MDS with Microsoft Active Directory.
Answer: B
Explanation:
Section: Storage Network
Explanation
NEW QUESTION 59
A customer reports that the Chassis Management Controller fails to receive chassis information from Cisco UCS Manager Which set of steps resolves the issue?
- A. 1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level.
2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly.
3) Check for runtime link down status
4) Reseat the affected IOM. - B. 1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level.
2) Verify that at least two physical cables between the IOM and fabric interconnect function properly.
3) Check for runtime link down status.
4) Reseat the affected IOM. - C. 1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels
2) Verify that at least two physical cables between the IOM and fabric interconnect function properly.
3) Check for runtime link down status
4) Reseat the affected IOM. - D. 1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels.
2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly.
3) Check for runtime link down status.
4) Reseat the affected IOM.
Answer: A
NEW QUESTION 60
......
Use Real 300-615 Dumps - 100% Free 300-615 Exam Dumps: https://www.dumps4pdf.com/300-615-valid-braindumps.html
300-615 Exam Dumps, Test Engine Practice Test Questions: https://drive.google.com/open?id=1m29SRakL6L_MFZm7LJv2FP3p58ooTuuI