Latest [Sep 26, 2021] 300-615 Exam with Accurate Troubleshooting Cisco Data Center Infrastructure PDF Questions
Take a Leap Forward in Your Career by Earning Cisco 99 Questions
NEW QUESTION 20
An engineer must upgrade all components in a Cisco UCS domain to the same package version, but the upgrade process fails to complete. Which set of Auto Install actions resolves the problem?
- A. Install Server Firmware, then Install Infrastructure Firmware
- B. Install Hypervisor Firmware, then Install Infrastructure Firmware
- C. Install infrastructure Firmware, then Install Hypervisor Firmware.
- D. Install Infrastructure Firmware, then Install Server Firmware.
Answer: D
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/firmware-mgmt/gui/2-5/b_GUI_Firmware_Ma
NEW QUESTION 21
Drag and drop the Cisco UCS SNMP fault types from the left onto the correct issues on the right.
Answer:
Explanation:
NEW QUESTION 22
Refer to the exhibit.
An engineer is troubleshooting why user1, user2, and user3 from group STORAGE- ADMINISTRATOR in Microsoft Active Directory cannot log in to the Cisco MDS SSH CLI. Which action resolves the issue?
- A. Configure SSH logins on Cisco MDS switch.
- B. Include specific users into MDS role configuration.
- C. Integrate Cisco MDS with Microsoft Active Directory.
- D. Configure the role name to match the group name on Microsoft Active Directory.
Answer: D
NEW QUESTION 23
Refer to the exhibit.
HSRP adjacency fails to form between Nexus7K-1 and Nexus7K-2. Which action should be taken to solve the problem?
- A. Configure the correct subnet mask on Nexus7K-1.
- B. Configure preempt on one of the switches in the HSRP group.
- C. Configure the same HSRP priority between the two switches.
- D. Configure HSRP version 2 on Nexus7K-2.
Answer: D
NEW QUESTION 24 
Refer to the exhibit. The connection between a Cisco Nexus 5548UP switch and a Cisco MDS switch fails to initialize. What is the cause of the issue?
- A. VSAN 1 is suspended.
- B. Trunk mode must be activated.
- C. The SFP is unsupported.
- D. The interface is in an incorrect mode.
Answer: B
Explanation:
Section: Storage Network
NEW QUESTION 25 
Refer to the exhibit. An engineer is performing a health check on ACI. Which statement about interface Ethernet 1/11 is true?
- A. The interface is working correctly and fully operational, but it is not in use.
- B. "out-of-service" indicates that no service graph is in use for this interface.
- C. "out-of-service" is the default interface status in ACI.
- D. The interface policy is misconfigured.
Answer: D
Explanation:
Section: Compute Platforms
NEW QUESTION 26
Refer to the exhibit.
Interface fc1/5 is offline. Which action should be taken to troubleshoot the issue?
- A. Configure the upstream ports and the server ports to be in VSAN 100.
- B. Update the FLOGI database to contain the FLOGI entries for interface fc1/5 in VSAN 100.
- C. Activate the correct zoneset for VSAN 100.
- D. Update the FCNs database to contain names for VSAN 100.
Answer: A
NEW QUESTION 27
Drag and drop the actions from the left onto the faults that they resolve on the right. Not all options are used.
Answer:
Explanation:
NEW QUESTION 28
Refer to the exhibit.
Cisco UCS Manager is being upgraded using the Auto Install feature, but the FSM fails. Which action resolves the issue?
- A. Acknowledge the primary fabric interconnect.
- B. Remove the service pack from the subordinate fabric interconnect.
- C. Clear the startup version of the default infrastructure pack.
- D. Upgrade the firmware of the infrastructure firmware by using the force option.
Answer: C
NEW QUESTION 29
A server administrator attempts to change the Cisco IMC KVM certificate to one that is signed by a private CA, but the certificate is not accepted. What causes this process to fail?
- A. omitting the public IP address of the Cisco IMC in the SAN
- B. using RSA encryption in the generation of the certificate
- C. using a certificate with a password-protected private key
- D. using AES encryption in the generation of the certificate
Answer: C
Explanation:
Section: Management and Operations
NEW QUESTION 30
An engineer is troubleshooting issues in Cisco UCS Director. Drag and drop the possible causes from the left onto the correct issues on the right.
Answer:
Explanation:
NEW QUESTION 31
Refer to the exhibits.
An engineer troubleshoots switch N5K1, which fails to receive traffic from the file server Which set of actions resolves this problem?
- A. Assign native VLAN 10 with fc2.'l - 2 and allow VLAN 10 in trunk configuration.
- B. Bind native VLAN 10 with Ethemet1/10 and allow VSAN 101 in trunk configuration.
- C. Assign native VLAN 10 with vfc111 and allow VLAN 1101 in trunk configuration.
- D. Bind native VLAN 10 with Ethemet10/1/1 and allow VLAN 10 in trunk configuration
Answer: B
NEW QUESTION 32
A server fails to boot from the operating system after a RAID1 cluster migration. The RAID remains in an inactive state during and after a service profile association. Which action resolves the issue?
- A. Use a predefined local disk configuration policy.
- B. Configure the SAN boot target to any configuration mode.
- C. Remove the local disk configuration policy.
- D. Configure the SAN boot target in the service profile.
Answer: A
NEW QUESTION 33
Refer to the exhibit.
During implementation of a Cisco UCS C-Series Server, an engineer receives the status that is shown in the exhibit. Which action resolves the issue.
- A. Set SLOT-1 Sync Mode to "Auto"
- B. Configure the RAID that is associated with the card.
- C. Insert an SD card into SLOT-2
- D. Reconfigure the Drive Type from "Removable" to "Non-Removable"
Answer: D
NEW QUESTION 34
Refer to the exhibit.
An engineer is investigating a role mapping issue on a switch. The users report that they cannot view the IP addresses under the tenant "corp". Which action resolves the issue?
- A. Configure the correct secret password between the APIC and the RADIUS server.
- B. Add the updated avpair to include/corp/admin/
- C. Update the UNIX ID.
- D. Add the users to the RADIUS server.
Answer: A
NEW QUESTION 35
Refer to the exhibit.
The initiator that has FC ID 0x970102 fails to communicate with the target that has FC ID 0x970200. What action resolves the issue?
- A. Reconfigure the initiator and the target to be in the same zones.
- B. Reset the port for FC ID 0x970102 and FC ID 0x970200 to log in to the fabric.
- C. Reactivate the zoneset.
- D. Reset the port for FC ID 0x970209 and FC ID 0x9700c2 to log in to the fabric.
Answer: C
NEW QUESTION 36
Cisco Unified Computing System Manager raises a critical error message that indicates that the system has overlapping Ethernet and FCoE VLANs. All of the Ethernet traffic on the overlapping VLANs drops. Which action resolves the issue?
- A. Modify the VLAN assignment to vNICs.
- B. Change the PIN groups on the vHBAs.
- C. Modify the FCoE VLAN.
- D. Set the FCoE VLAN as the native VLAN on server uplinks.
Answer: A
NEW QUESTION 37
Refer to the exhibit.
The connection between a Cisco Nexus 5548UP switch and a Cisco MDS switch fails to initialize. What is the cause of the issue?
- A. VSAN 1 is suspended.
- B. Trunk mode must be activated.
- C. The SFP is unsupported.
- D. The interface is in an incorrect mode.
Answer: B
NEW QUESTION 38
Refer to the exhibit.
Sw1 and Sw2 are two Cisco Nexus 9000 Series Switches that run Cisco NX-OS. They are VTEPs in the same vPC domain. Which statement describes what happens in this scenario?
- A. Sw1 and switch 2 perform the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs, depending on the hashing.
- B. Sw2 did not send an IP PIM register to the rendezvous point for the multicast group of the VXLAN VNI.
- C. Sw1 performs the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs.
- D. Sw1 drops all traffic because there is no (S, G) OIF list to encapsulate VXLAN multicast packets and send them out to the underlay network through the uplink interfaces.
Answer: C
NEW QUESTION 39
Drag and drop the Cisco UCS SNMP fault types from the left onto the correct issues on the right.
Answer:
Explanation:
NEW QUESTION 40
An engineer discovers that an NPV/NPIV uplink experiences a heavy load and plans to add more uplinks.
Which statement about what occurs when the new uplinks are added is true?
- A. All connections must be reset before the new uplinks can be used.
- B. Paths must be defined before new connections can use the new uplinks.
- C. New and existing connections use the new uplinks automatically.
- D. Only new connections use the new uplinks automatically.
Answer: C
NEW QUESTION 41
Refer to the exhibit.
The HSRP configuration in the exhibit fails to function. Which action resolves this issue?
- A. Configure HSRP version 2.
- B. Set the MTU to 1500 bytes.
- C. Enable IP redirects.
- D. Configure the same HSRP group on both devices.
Answer: A
NEW QUESTION 42
......
Authentic Best resources for 300-615 Online Practice Exam: https://www.dumps4pdf.com/300-615-valid-braindumps.html
Practice To 300-615 - Dumps4PDF Remarkable Practice On your Troubleshooting Cisco Data Center Infrastructure Exam: https://drive.google.com/open?id=1-1_MfMGvVRo3VdPaVeHGNkBRg40UsZ4m